Today, I am going to share some good news with Samsung Galaxy Tab 4 7.0 Wi-Fi users. Now you can enjoy a new firmware update on your device. Android 4.4.2 KitKat XXU0ANE6 has been released for Galaxy Tab 4 7.0 Wi-Fi. Well, I have recently published an article for updating Samsung Galaxy Note 10.1 to KitKat XXUDNE4. Now you can update Samsung Galaxy Tab 4 7.0 Wi-Fi to Android 4.4.2 KitKat XXU0ANE6.
This is really a great news for Galaxy Tab 4 7.0 Wi-Fi users. You can experience the improvement after installing KitKat XXU0ANE6. The good news is that you can easily root your Samsung Galaxy Tab 4 7.0 Wi-Fi after installing KitKat XXU0ANE6. Well, you don’t need to install CWM recovery on Galaxy Tab 4 7.0 before updating it. My dear friend don’t forget to backup your messages, and contacts available on Galaxy Tab 4 before following the steps. Samsung Galaxy Tab 4 7.0 Wi-Fi USB driver need to be installed on your PC for successful connection between your Galaxy Tab 4 7.0 and PC.
Now you must be eagerly waiting to enjoy the new firmware on your Galaxy Tab 4. Below are the steps using which you can install KitKat XXU0ANE6 on Samsung Galaxy Tab 4 7.0 Wi-Fi. Androidbiits will not be responsible if your Galaxy Tab 4 got corrupted during the update process. Your Samsung Galaxy Tab 4 7.0 Wi-Fi battery level must be above 92% before following these steps.
How to Install Android 4.4.2 KitKat XXU0ANE6 on Samsung Galaxy Tab 4 7.0 Wi-Fi
1. First you have to download Android 4.4.2 KitKat XXU0ANE6 on your PC from the given link.
sammobile.com/firmwares/3/?download=30253
2. Now you have to download Odin to install XXU0ANE6 on your Galaxy Tab 4 7.0.
devfiles.co/download/CAHmXM6c/Odin_v3.09.zip
3. Now you have to put your Galaxy Tab 4 7.0 into download mode using these steps:
- Turn off your 7-inch Samsung Tab 4.
- Press Galaxy Tab 4 7.0 volume down button and home button simultaneously.
- Press Galaxy Tab 4 7.0 Power button at the same time while pressing the Home button and volume down button. You will be able to view a warning message on your Galaxy Tab 4 7.0 after some time.
- Press Galaxy Tab 4 Power button again after viewing this warning message to put it into download mode.
4. Launch Odin on your PC and connect your Samsung Galaxy Tab 4 7.0 Wi-Fi with your PC via USB cable.
5. You can see a message in the bottom left corner of Odin after connecting your 7-inch Samsung Tab 4 with your PC.
6. Now you have to extract the ZIP file of KitKat XXU0ANE6 on your PC downloaded in STEP 1.
7. Once you have successfully extracted the ZIP file of KitKat XXU0ANE6, you have to press “PDA” in Odin and choose “.tar.md5″ file.
8. Now you have to press “PDA” in Odin and choose “modem” file.
9. Now you have to press “CSC” in Odin and choose “csc” file.
10. Press “PIT” in Odin and choose “.pit” file.
11. Now you have to press the “Start” button in Odin after selecting “Re-Partition” and “Auto-reboot” options.
You will have to wait until your Samsung Galaxy Tab 4 7.0 Wi-Fi restarts. It may take around 6 minutes to reboot. Once your Galaxy Tab 4 is restarted, you can enjoy KitKat XXU0ANE6. If you are facing any difficulty while installing KitKat XXU0ANE6, then you can share your difficulty with me in the comment section below.